glusterfs.git/tests/bugs/bug-884455.t, branch v6.10

tests: move all test-cases into component subdirectories

2015-01-06T11:24:24+00:00

There are around 300 regression tests, 250 being in tests/bugs. Running
partial set of tests/bugs is not easy because this is a flat directory
with almost all tests inside.

It would be valuable to make partial test/bugs easier, and allow the use
of mulitple build hosts for a single commit, each running a subset of
the tests for a quicker result.

Additional changes made:
- correct the include path for *.rc shell libraries and *.py utils
- make the testcases pass checkpatch
- arequal-checksum in afr/self-heal.t was never executed, now it is
- include.rc now complains loudly if it fails to find env.rc

Change-Id: I26ffd067e9853d3be1fd63b2f37d8aa0fd1b4fea
BUG: 1178685
Reported-by: Emmanuel Dreyfus 
Reported-by: Atin Mukherjee 
URL: http://www.gluster.org/pipermail/gluster-devel/2014-December/043414.html
Signed-off-by: Niels de Vos 
Reviewed-on: http://review.gluster.org/9353
Reviewed-by: Kaleb KEITHLEY 
Reviewed-by: Emmanuel Dreyfus 
Tested-by: Gluster Build System 
Reviewed-by: Vijay Bellur

tests: Use uniform timeouts

2014-05-20T04:00:46+00:00

Change-Id: I479ab941b3b2da3b16f624400fbd300f08326268
BUG: 1092850
Signed-off-by: Pranith Kumar K 
Reviewed-on: http://review.gluster.org/7799
Tested-by: Gluster Build System 
Reviewed-by: Anand Avati

tests: call 'cleanup' at the end of each test

2013-07-15T17:44:27+00:00

Some tests do not cleanup after themselves. That is bad behaviour and
makes it difficult to run single tests and verify the state of the
system afterwards.

Change-Id: I4ac5401d790d6bc81e6975fd1384874b21d6cf8a
BUG: 983975
Signed-off-by: Niels de Vos 
Reviewed-on: http://review.gluster.org/5328
Tested-by: Gluster Build System 
Reviewed-by: Kaleb KEITHLEY 
Reviewed-by: Anand Avati

tests/bugs: Increase timeout for rebalance completion check

2013-05-31T08:03:25+00:00

Change-Id: Ic299c0d7b3996f6e85f9627430efbdf3f9ea0a8f
BUG: 884455
Signed-off-by: shishir gowda 
Reviewed-on: http://review.gluster.org/4942
Reviewed-by: Vijay Bellur 
Tested-by: Gluster Build System

cluster/distribute: Fix layout overlaps due to spread-count in selfheal path

2013-03-08T03:51:22+00:00

We needed to zero out the layout range, before we re-calculate the range.
When spread-count is issued, we would end up with stale ranges in the layout.

Replaced dht_selfheal_dir_xattr with dht_fix_dir_xattr, which correctly resets
the un-used (after re-cal) layouts.

Change-Id: I1a900d15df07335f59356bd23182ccec34381ab2
BUG: 884455
Signed-off-by: shishir gowda 
Reviewed-on: http://review.gluster.org/4647
Reviewed-by: Amar Tumballi 
Tested-by: Gluster Build System 
Reviewed-by: Jeff Darcy

cluster/distribute: re-set layouts to prevent overlaps

2012-12-12T00:05:50+00:00

When subvols-per-directory option is used, with bricks addition/removal
the layouts might get distributed to other subvols, which were not part
of the layout before. We need to clean up layouts on old subvolumes, to
prevent overlaps.

Also, we need to make sure if layout-cnt is never less
than subvolume-cnt.

Change-Id: I00994a092ca0c99aedcc41bd9412d43460f88a04
BUG: 884455
Signed-off-by: shishir gowda 
Reviewed-on: http://review.gluster.org/4281
Tested-by: Gluster Build System 
Reviewed-by: Anand Avati